Cressida - 13s for $1300 project

[OKE020]

Stuff it, entered, i'm not a sit in the stands person...... well atleast until i get out round 1 haha

[tim510]

race ya!

[OKE020]

bring it

[RNS-11Z]

scott, you taking this out this wednesday?

[IS SLO]

Nice. Will be good to see the granny spec stur up the street class.

[OKE020]

scott, you taking this out this wednesday?

I have been thinking about it. Got my aem wide band back now, would not mind tidying up the map and maybe trying a pass with a smaller shot but for the entire pass. Would be awesome to crack 140 so I can bolt a chute on for Jambo haha. More accurate outcome is I will probably be looking for another box on Thursday haha

[747]

Stuff it, entered, i'm not a sit in the stands person...... well atleast until i get out round 1 haha

good to hear man

[Paydirt]

I think I'm on the start line Wed.... I didn't see anything

[RNS-11Z]

I have been thinking about it. Got my aem wide band back now, would not mind tidying up the map and maybe trying a pass with a smaller shot but for the entire pass. Would be awesome to crack 140 so I can bolt a chute on for Jambo haha. More accurate outcome is I will probably be looking for another box on Thursday haha

hahahaha imagine it goes 9.90
i might take mine out too. see how it goes

[OKE020]

Track should be ok as I think there has been some private test days

[ALLMTR]

What would a fully built auto cost? What's it weigh?

[sleepercorty]

What would a fully built auto cost? What's it weigh?

mine cost me $350 mv valve body, $400 in parts and $700 for a gearbox shop to assemble it with the extra clutches. it makes around 600rwhp in full weight cressida and seems to have no dramas with the power so they are a good gearbox and fairly cheap to build. the weak point in my opinion would be the input shaft they are not very big.

i was going to enter Jamboree but couldnt be bothered putting a harness in and turning the boost down to run over 11.00 if i knew you were entering i might of made the effort, i may still enter dyno but will see

[Supercrown]

Yep - input shaft snaps off in the converter, and there is no way to make a shaft from better material due to the shaft design.

Once you are past about 450rwkw it becomes a gamble (although that threshold does shift up and down depending on the valvebody - ie on shift hardness, tyres, vehicle weight and road surface)

[tim510]

Track should be ok as I think there has been some private test days

some rotor dudes are hiring the track tomorow for testing. a couple of pro-cars and a 20B 1200 ute with all the fruit.

[OKE020]

Yep i just need to see if i could be bothered braking the box / engine and trying to source another before jamboree. Worst case will go out for a look anyway

[tim510]

Yep i just need to see if i could be bothered braking the box / engine and trying to source another before jamboree. Worst case will go out for a look anyway

I might do the same. I gave about 30secs consideration to taking the BB out, but I CNBF'd and its still got a few things that need to be done.

[Shifty]

Yep i just need to see if i could be bothered braking the box / engine and trying to source another before jamboree. Worst case will go out for a look anyway

might be a good way to run it up on the aem and sort it in the deep end, so you know it's good for jambo

better blowing it up now and having time to sort it, than on your first pass at jambo

[millsi]

Yep i just need to see if i could be bothered braking the box / engine and trying to source another before jamboree. Worst case will go out for a look anyway

Leave NOS at home?

[RNS-11Z]

some rotor dudes are hiring the track tomorow for testing. a couple of pro-cars and a 20B 1200 ute with all the fruit.

Do you think it will be a busy night at the track for a TnT?

[tim510]

Very! Lots of jambo prep! It's always a bit meet pre jambo

[RNS-11Z]

cool thanks, i think i might head out after jambo then.

[21OWA]

Awesome work Scott

Might have to give u a run at powercruise
See how my boat goes against a genuine 10sec streeter

[ALLMTR]

When is this going out again?

[OKE020]

It's just on daily and Thursday night cruise duties at the moment. Been busy trying to get a turbo 398 Cleveland xw ready so I can drive it in TSB at the shoot out in 3 weeks

[BoganDAVE]

pics of XW stat!

[Shifty]

it has the biggest turbo i've ever seen on a car lol

[OKE020]

Work in progress engine pic

[BoganDAVE]

e85 / meth?

[OKE020]

E85 but I want to go c16 + meth enrichment as the fuel system is not quite there for the power he wants to make on e85

[BoganDAVE]

What fuel system?