Page 14 of 16 FirstFirst ... 410111213141516 LastLast
Results 391 to 420 of 462

Thread: CHP racecar v4.0

  1. #391
    Chairbourn ranger! Mike Lowrrryyy's Avatar
    Join Date
    May 2007
    Location
    Newcastle
    Posts
    11,096
    Fucken Dale and his WOT only tunes.
    Quote Originally Posted by S View Post
    I just want to apologise for some of my shit talking back around page 5.

  2. #392
    sack riding 10sec rx7's Avatar
    Join Date
    Nov 2001
    Location
    Sydney
    Posts
    18,321
    so after looking at all the photos from the weekend chris has decided he does not like the piping and fuel tank (it was made when it still had the rad support panel etc on it),.. so hes going to remake them... so may as well re plumb the car in speedflow 550 series light weight hose.. should save 15-20LB off the nose..
    im a cunt
    and apparently i dont know shit...

  3. #393
    Registered User GSRman's Avatar
    Join Date
    Nov 2001
    Location
    Caught in the ACT
    Posts
    17,625
    Figure out what the little bit of vapour was?

    Sent from my Pixel 2 XL using Tapatalk
    This is a post i wrote by mistake, which is nice...

  4. #394
    sack riding 10sec rx7's Avatar
    Join Date
    Nov 2001
    Location
    Sydney
    Posts
    18,321
    couldnt see anything today when i pulled the injectors and rockers off... my guess is the tubes to the rear tank are blocked with fluid (they empty when you let go of the trans brake) and it was just pushing some fumes out the connectors..
    im a cunt
    and apparently i dont know shit...

  5. #395
    Custon User Title Borked Cplus's Avatar
    Join Date
    Nov 2001
    Location
    the backwater
    Posts
    10,006
    Whatís the qtr mile goal for this? What does the 4.7 for 1/8th translate into for full track?
    Public Service Reminder

    Quote Originally Posted by boostin31 View Post
    I once 1/2 filled a powerade bottle with piss at a daft punk concert then launched it. I doubt the person on the receiving end even knew what hit them though.

  6. #396
    sack riding 10sec rx7's Avatar
    Join Date
    Nov 2001
    Location
    Sydney
    Posts
    18,321
    4.7 would give you a 6.. have gone 4.3 in the 1/8
    im a cunt
    and apparently i dont know shit...

  7. #397
    no mods, leave it stock Jack Nicholson's Avatar
    Join Date
    Aug 2012
    Location
    B̶e̶v̶e̶r̶l̶y̶ ̶H̶i̶l̶l̶s̶,̶ ̶C̶A̶ Baulkham Hills, NSW
    Posts
    6,447
    I guess the short service life of the components makes it a bit tough to develop the motor and tune?

    I mean if ten runs on the dyno takes a quarter of the service life of the motor before it needs new rods, it's not like you can make a whole day of pulls on the dyno and get the tune absolutely where you want it right?

    Must be frustrating finding that balance...
    Jaguar XJR, Freelander 2 HSE, Jaguar XKR

    Quote Originally Posted by Marv View Post
    Look, just because you drive a couple of imported luxo Pommy cars doesn't mean you need to act like an Imperialistic Lapdog and be the last bastion of defence for Straya The Beaut's mid-20th-Century ideals
    Quote Originally Posted by nutttr View Post
    People must assume you are some sort of drug dealer with all these nice cars turning up to a fibro home

  8. #398
    sack riding 10sec rx7's Avatar
    Join Date
    Nov 2001
    Location
    Sydney
    Posts
    18,321
    As long as your not changing major parts like fuel injectors etc then itís not too bad, putting a set of rods in does not change anything to do with the tune,

    The Ecu corrected .2% on the 2 lower boost runs, it did peg out at my max of 5% I allow it to pull on the high boost run.

    Chassis tuning is more the issue trying to use the power on these little Tyres
    im a cunt
    and apparently i dont know shit...

  9. #399
    aka SpaZdA (tm) mondo2000's Avatar
    Join Date
    Nov 2001
    Location
    Brisbane
    Posts
    1,378
    So you life engine components based on the number of hits they've had, regardless if they were 1/8 mile, 1/4 mile or dyno? Surely a couple of seconds of WOT on the dyno wouldn't use stuff up as much as a burnout, bump in on the 2 step and a full quarter mile pass?

  10. #400
    Down with ma homies Greg Rust's Avatar
    Join Date
    Dec 2006
    Location
    Perf
    Posts
    11,048
    Can I buy a signed rod from this engine?
    2017 Ford Ranger XLT (Jeep Wrangler recovery vehicle)
    2007 KTM 250 SX

    Quote Originally Posted by Monza View Post
    I've never considered myself the type of guy to eat arse but I am currently reviewing that policy

  11. #401
    Registered User
    Join Date
    Aug 2013
    Location
    gawler
    Posts
    2,092
    Fuck yeah! I'll have one as well.
    " Racing cars don't have doors. Toilets have doors" : Keke Rosberg

  12. #402
    sack riding 10sec rx7's Avatar
    Join Date
    Nov 2001
    Location
    Sydney
    Posts
    18,321
    Quote Originally Posted by mondo2000 View Post
    So you life engine components based on the number of hits they've had, regardless if they were 1/8 mile, 1/4 mile or dyno? Surely a couple of seconds of WOT on the dyno wouldn't use stuff up as much as a burnout, bump in on the 2 step and a full quarter mile pass?
    I class a 3x 1/8 mile hits the same as 2x 1/4 mile hits.. and the dyno runs ill put down as 3 passes... so 40 1/4 mile passes on a set of rods which may end up as 50-60 1/8 mile.. BUT if the engine has a big misfire or lean out etc the rods will get changed pretty quickly..
    im a cunt
    and apparently i dont know shit...

  13. #403
    sack riding 10sec rx7's Avatar
    Join Date
    Nov 2001
    Location
    Sydney
    Posts
    18,321
    when I swap the rods over ill send you boys some
    im a cunt
    and apparently i dont know shit...

  14. #404
    Chairbourn ranger! Mike Lowrrryyy's Avatar
    Join Date
    May 2007
    Location
    Newcastle
    Posts
    11,096
    Everyone loves Dales rod(s).
    Quote Originally Posted by S View Post
    I just want to apologise for some of my shit talking back around page 5.

  15. #405
    sack riding 10sec rx7's Avatar
    Join Date
    Nov 2001
    Location
    Sydney
    Posts
    18,321
    Iíve got a box of them here actually, they are a little beat up... but be perfect for hanging up in the garage
    im a cunt
    and apparently i dont know shit...

  16. #406
    Down with ma homies Greg Rust's Avatar
    Join Date
    Dec 2006
    Location
    Perf
    Posts
    11,048
    Wicked. Thanks b.
    2017 Ford Ranger XLT (Jeep Wrangler recovery vehicle)
    2007 KTM 250 SX

    Quote Originally Posted by Monza View Post
    I've never considered myself the type of guy to eat arse but I am currently reviewing that policy

  17. #407
    Registered User
    Join Date
    Nov 2001
    Location
    Melbourne
    Posts
    1,398
    I'd love a bit of Dale rod action too.

    Perfect for the garage wall.

    Happy to pay too
    Ban low performance drivers not high performance cars

  18. #408
    Registered User [RX3]'s Avatar
    Join Date
    Oct 2002
    Posts
    1,256
    Quote Originally Posted by turbo510 View Post
    I'd love a bit of Dale rod action too.

    Perfect for the garage wall.

    Happy to pay too
    x 2

  19. #409
    Gimme six Schlitzes Beavis's Avatar
    Join Date
    Nov 2001
    Location
    Hanover, NH, USA
    Posts
    7,301
    Me three

  20. #410
    Registered User
    Join Date
    Jun 2007
    Location
    QLD / NZ
    Posts
    498
    Iíd love a rod too mate if possible. Happy to swap for beer

    Congrats on the power too man thatís seriously impressive!
    Last edited by toyabusa; 09-01-19 at 01:51 PM. Reason: Iím a spaz

  21. #411
    Registered User GSRman's Avatar
    Join Date
    Nov 2001
    Location
    Caught in the ACT
    Posts
    17,625
    dudes line'n up for dales rod.
    This is a post i wrote by mistake, which is nice...

  22. #412
    sack riding 10sec rx7's Avatar
    Join Date
    Nov 2001
    Location
    Sydney
    Posts
    18,321
    found 2 boxes today.... ill sort em out on saturday for you boys
    im a cunt
    and apparently i dont know shit...

  23. #413
    Registered User RNS-11Z's Avatar
    Join Date
    Feb 2003
    Location
    Brisbane
    Posts
    3,915
    Out of curiosity what happens to the rods? Do they bend?

  24. #414
    Arrogant wankeler Slides's Avatar
    Join Date
    Jul 2009
    Location
    Central West/Lake Macquarie
    Posts
    1,390
    Guessing it is more a fatigue life management thing, cheaper to replace rods early than rods and block when they snap.

  25. #415
    sack riding 10sec rx7's Avatar
    Join Date
    Nov 2001
    Location
    Sydney
    Posts
    18,321
    Quote Originally Posted by RNS-11Z View Post
    Out of curiosity what happens to the rods? Do they bend?
    they usually break...
    im a cunt
    and apparently i dont know shit...

  26. #416
    BLING BLING PLAYA's Avatar
    Join Date
    Mar 2002
    Location
    adelaide
    Posts
    6,398
    At what point does things become consumable? Could you say 1500 HP on this would be day in day out?
    3D scanning
    3D modelling
    Structural certification
    3 and 5 axis milling

  27. #417
    sack riding 10sec rx7's Avatar
    Join Date
    Nov 2001
    Location
    Sydney
    Posts
    18,321
    Quote Originally Posted by PLAYA View Post
    At what point does things become consumable? Could you say 1500 HP on this would be day in day out?
    At 1500 would have steel rods in it. Just like the camaro engine, last for ever at that
    im a cunt
    and apparently i dont know shit...

  28. #418
    Registered User
    Join Date
    Feb 2011
    Location
    SA
    Posts
    127
    Awesome! Nice work Dale. Did old mate make good on the bet?

  29. #419
    Registered User 2rismo's Avatar
    Join Date
    Jan 2003
    Location
    Wollongong
    Posts
    5,430
    Quote Originally Posted by fnlow View Post
    Awesome! Nice work Dale. Did old mate make good on the bet?
    Yep, Dale got "PSI blown" that night.
    Quote Originally Posted by piss98
    I wish Kochie would get blown out to sea and never found, in fact most of those dumb cunts standing in the rain telling people not to stand in the rain need to get fucked. Stupid tart on the news last night talking to the weather guy "wow you look totally drenched there whateverthefuckhisnamewas." No shit you vapid bitch he is standing in a fucking cyclone.

  30. #420
    sack riding 10sec rx7's Avatar
    Join Date
    Nov 2001
    Location
    Sydney
    Posts
    18,321


    When you speak to your trans builder on the Monday and he says your going to fucking die if you donít put a Reid case on the box...
    im a cunt
    and apparently i dont know shit...

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •